Stone Coated Roof Production Line Stone coated metal roofing was refined during and after World War II in the United Kingdom, when the government requested materials that would protect corrugated steel roofs from the harsh climate. A coating of bitumen and subsequent covering by sand, stone or other materials proved effective at protecting the metal roofs and serving as camouflage against potential attack. Now this type roofing sheet is quite popular in the market. Based on this need, we developed stone coated roofing sheet machine, the working speed could reach 25m/min. Stone Coated Roof Production Line, Stone Chip Coated Roofing Tile Machine Zhongtuo Roll Forming Machinery Co., ltd , https://www.frameforming.nl
First, the machine accessories (fixtures) should be coated with anti-rust oil;
Second, regular inspection of the machine for oil leakage, if there is oil leakage, should immediately replace the mat or seal, and according to the use of the machine and the use of oil, regular replacement filter, suction filter and hydraulic oil.
Third, each test should be completed after the test machine jaws to clean up, keep it clean.
Fourth, if it is not a machine for a long time, you should turn off the computer and controller. Regularly check the configuration of the machine and keep the machine in good working condition. If parts are loose and fall off, they should be repaired in time. The interface on the plug-in controller must turn off the power of the controller. The interfaces on the controller are one-to-one. If there is a wrong interface, the device may be damaged. If the machine is in the standby state, the switch should be “loadedâ€. Because if the switch is in the “reverse†position, the solenoid valve is always on, which will affect the life of the device.
5. Regularly inspect the screws at the jaws. If any looseness is found, tighten it in time and check the transmission condition of the sprocket regularly. If there is any looseness, tighten the tensioning wheel.
6. The sliding surface that is in contact with the steel plate and the liner plate and the dovetail groove surface on the liner shall be kept clean from time to time, and a thin layer of molybdenum disulfide (MoS2) grease shall be regularly coated; the electronic universal testing machine is currently the more common teaching method. Testing equipment is mainly provided to universities and research institutes. Because of its teaching purpose, its use rate is relatively high. Therefore, the frequent use of electronic universal testing opportunities leads to shortened service life. Therefore, proper and effective maintenance is particularly important. Jiangsu Tianhui tensile testing machine here to share the correct way to maintain and maintain the electronic universal testing machine.
First, the machine accessories (fixtures) should be coated with anti-rust oil;
Second, regular inspection of the machine for oil leakage, if there is oil leakage, should immediately replace the mat or seal, and according to the use of the machine and the use of oil, regular replacement filter, suction filter and hydraulic oil.
Third, each test should be completed after the test machine jaws to clean up, keep it clean.
Fourth, if it is not a machine for a long time, you should turn off the computer and controller. Regularly check the configuration of the machine and keep the machine in good working condition. If parts are loose and fall off, they should be repaired in time. The interface on the plug-in controller must turn off the power of the controller. The interfaces on the controller are one-to-one. If there is a wrong interface, the device may be damaged. If the machine is in the standby state, the switch should be “loadedâ€. Because if the switch is in the “reverse†position, the solenoid valve is always on, which will affect the life of the device.
5. Regularly inspect the screws at the jaws. If any looseness is found, tighten them in time and check the transmission condition of the sprocket regularly. If there is any looseness, tighten the tension pulley again;
6. The sliding surface that is in contact with the steel plate and the liner plate and the dovetail groove surface on the liner shall be kept clean from time to time, and a thin layer of molybdenum disulfide (MoS2) grease shall be regularly coated; the electronic universal testing machine is currently the more common teaching method. Testing equipment is mainly provided to universities and research institutes. Because of its teaching purpose, its use rate is relatively high. Therefore, the frequent use of electronic universal testing opportunities leads to shortened service life. Therefore, proper and effective maintenance is particularly important. Jiangsu Tianhui tensile testing machine here to share the correct way to maintain and maintain the electronic universal testing machine.
First, the machine accessories (fixtures) should be coated with anti-rust oil;
Second, regular inspection of the machine for oil leakage, if there is oil leakage, should immediately replace the mat or seal, and according to the use of the machine and the use of oil, regular replacement filter, suction filter and hydraulic oil.
Third, each test should be completed after the test machine jaws to clean up, keep it clean.
Fourth, if it is not a machine for a long time, you should turn off the computer and controller. Regularly check the configuration of the machine and keep the machine in good working condition. If parts are loose and fall off, they should be repaired in time. The interface on the plug-in controller must turn off the power of the controller. The interfaces on the controller are one-to-one. If there is a wrong interface, the device may be damaged. If the machine is in the standby state, the switch should be “loadedâ€. Because if the switch is in the “reverse†position, the solenoid valve is always on, which will affect the life of the device.
5. Regularly inspect the screws at the jaws. If any looseness is found, tighten them in time and check the transmission condition of the sprocket regularly. If there is any looseness, tighten the tension pulley again;
6. The sliding surface in contact with the lining plate and the liner plate and the dovetail groove surface on the lining plate shall be kept clean at all times, and a thin layer of molybdenum disulfide (MoS2) grease shall be regularly applied.
Electronic universal testing machine maintenance
Electronic universal testing machine is currently a relatively common teaching and testing equipment, mainly for universities, research institutions and so on. Because of its teaching purpose, its use rate is relatively high. Therefore, the frequent use of electronic universal testing opportunities leads to shortened service life. Therefore, proper and effective maintenance is particularly important. Jiangsu Tianhui tensile testing machine here to share the correct way to maintain and maintain the electronic universal testing machine.