Medical Waste Transfer Vehicle Specifications

                                    Medical Waste Transfer Vehicle Specifications

 

      The medical waste transfer vehicle is also known as the medical waste transporter , medical waste transporter , medical garbage collection vehicle , and medical garbage transfer vehicle . In 2003, China's SARS outbreak and spread rapidly across the country, all medical institutions to become the first battlefield against SARS. SARS can be spread through droplets, the infection is very strong. At the same time, a large number of patients, resulting in a large number of medical waste, for this may carry infectious germs very high medical waste, transport and process must be rigorous protection, to prevent the spread of germs.

   It is in this case, based on the response to SARS demand, an urgent need to regulate medical waste transport vehicles to ensure transport safety, when the State Environmental Protection Administration issued an emergency to develop "medical waste transfer vehicle technical requirements" standard task, after preparation group preparation tense, in May 2003, the former State environmental Protection Administration jointly AQSIQ and the national Development and Reform Commission issued the GB 19217-2003 "medical waste transfer vehicle technical requirements (for trial Implementation)." the standard specific to medical waste transport vehicles performance requirements were clearly defined, put forward compartment seal, bottom barrier properties, as well as the compartment surface corrosion and other environmental technical requirements. after the promulgation of standards, which immediately became the country medical waste transfer vehicles in the fight against SARS tender The basis of purchase .

    Medical waste transfer vehicle characteristics: The characteristics of the design of medical waste, the use of airtight transport, the back door is double sealed structure, and the labyrinth seal, so that the compartment is completely closed, in order to achieve the effect of preventing the diffusion of toxic medical waste compartment bacteria in vivo. Wall panels are made of stainless steel , which can be sterilized by corrosive disinfection . Around the bottom of the cabin and round the corners , it is advisable to clean the corners for disinfection . The body of the vehicle has a UV disinfection function. When the UV lamp works normally, it radiates a large amount of ultraviolet rays of 253.7 nm , which is extremely powerful against microorganisms and kills bacteria within 30-45 minutes . Products with a closed, impermeable, dust and other performance; with antibacterial, flame retardant, corrosion-resistant, and easy cleaning and disinfection function.

    Sterilization method for medical waste transfer vehicles : Antivirus (optional) at low temperature , ultraviolet disinfection , and drug spray antivirus .

   Remarks: The external material of the car body is glass steel , the inside is stainless steel , with sprayer and germicidal lamp . The entire vehicle can be equipped with " Huatai " refrigeration units, with a minimum temperature of -5 degrees Celsius.

   Vehicle procedures    Chassis certification , vehicle certification , vehicle tools , vehicle warranty manual , national service station directory

   Corporate website: Sales Phone: 18727982266   0722-3325000

   Fax: 0722-3324444 Business Website:

Weld Materials

1.Welding materials

In Welding, substances called filler materials or consumables are used. As the name implies, these substances provide filler or a body of molten materials that provides a strong bond to be formed between the base metals used. Most welding processes will also require some form of shielding to protect both the main components and filler from being oxidized during the process.


The type of welding materials used during welding depends on the nature of the job intended. Electrodes draw the necessary energy in order to perform welding applications. Luoyang Golden Egret Company has any kind of welding materials include CTC Welding Rod /rope, SCTC welding rod/rope, TC electronic welding rod, Ni-based welding rod, flux-cored Welding Wires, solid welding wires and etc.

Welding can be applied in different kinds of industries such as building and construction, oil and gas, marine, power generation, steel, mine tools, automobile, transportation and etc.


2. Welding rod

1)Cast tungsten carbide based tubular rod

The hard phase of the rod is cast tungsten carbide which leads to higher hardness and better wear-resistance.

Wear resistance: the wear resistance is 6-7 times better than others. Tested by ASTM G65

Mainly used for Mining machinery, Geological tools, Petroleum drilling tools etc, by Oxy-Acetylene with weak carburizing flame.

Ni Based Welding Rod


Product recommendation:

GT1103 (CTC, 60-80 mesh),

GT1103-1(CTC, 20-30 um),

GT1103-2(CTC, 40-60 um)

2)The hard phase of tube rod is carbide pellets which leads to higher impact resistance and better wear resistance than CTC cloase rod.

Wear resistance: the wear resistance is 6-7 times better than others. Tested by ASTM G65 wear test.

Mainly used for mining machinery. Geological tools etc; by Oxy-acetylene with weak carburizing flame.

Product recommendation:

GT2102 (Cemented carbide grit, 30-60mesh)

GT2102-2(Cemented carbide grit, 30-40mesh)

GT2102-3(Cemented carbide grit, 40-60mesh)

3)Tube rod is composited by Cemented carbide pellets, Spherical CTC and CTC. The layer has higher impact resistance, better wear resistance and good fluidity than other rods.

Wear resistance: the wear resistance is 6-7 times better than others. Tested by ASTM G65.

Mainly used for oil method drill bits, such as Tri-cone bit, Steel tooth bit, PDC bit, etc. By Oxy-Acetylene with weak carburizing flame.

Product recommendation:

GT3302 (carbide pellets, 20-40mesh)

GT3302-1(carbide pellets, 14-40um)

4)The hard phase of the rod is monocrystal WC, the welding layer has a higher wear resistance and better impact resistance.

The wear resistance is 6-7 times better than others, tested by ASTM G65 method.

Mainly used for the repair and strength for oil drills bits, such as PDC bit diameter holding by Oxy-Acetylene with weak carburizing flame.

Product recommendation:

GT4104 (Monocrystal WC, 80-200mesh)

3. Welding Rope

Made form mixture of CTC and self-fluxing nickel alloy covering on nickel wire. The CTC is in spherical or irregular with good wear resistance; the nickel alloy is in spherical or nearly spherical shape with good wettability and erosion resistance and better corrosion resistance than tubular rod.

Recommend to use Petroleum drilling tools, Concrete mixing blade, Mud pump, Coal sluice, Coal drill pipe, Tunnel drilling machinery etc.

By Oxy-Acetylene Welding with weak carburizing flame.

5mm Welding Rope

Product recommendation:

GS110450N (CTC, 4mm, HRC 47-55)

GS110550N (CTC, 5mm, HRC 47-55)

GS110650N (CTC, 6mm, HRC 47-55)

4. Welding Bar

The rod is sintered by CTC and Ni-based powders. The CTC(Cast Tungsten Carbide) is in irregular or spherical shape with better wear resistance and the nickel alloy is in spherical or nearly spherical shape and has good wettability with cast tungsten carbide. The cladding layer has a higher impact resistance and better wear resistance.

Its wear resistance and corrosion resistance is between tube rod and flexible rope.

Mainly used on the Steel PDC bit, Concrete mixer blade, Mud pump, Miner chute, Miner drill stem and Mechanical parts of Tunnel rock drill machine etc.

Welded by Oxy-Acetylene with weak carburizing flame.

Product recommendation:

GD4025253-3(CTC, SCTC, 4*600/6*600)

GD4030303-3(CTC, SCTC, 4*600/6*600)

5. Welding wire

Intensified molybdenum titanium vanadium composite chromium carbide welding wire can improve layer`s bonding strength and tenacity. This wire can use for multilayer welding which has no peel off, and it can maintain good wear resistance under certain impact working condition.

Product recommendation:GSQD671Mo-4(1.6mm)

Medium carbon and high chromium wear resistance welding wire has a higher hardness, stronger wear resistance, and excellent toughness by adding a certain amount of molybdenum alloys and boride. It has a better impact resistance and strip resistance than high chromium cast iron type materials

Product recommendation: GSQD621Mo-4(1.6mm)

6. Tungsten Carbide Pellets

With high sphericity & excellent alloy organization, cemented carbide pellet is mainly used in welding, as an adding material of PTA Powder , tubular welding rod, to improve the wear resistance of the workpieces greatly.

Product recommendation: GQ06


Wc 6co Tungsten Carbide Pellets


7. Tungsten Carbide Grits

Cemented carbide grit with different percent of cobalt has good abrasive resistance and is widely used for making grinding, polishing and cutting tools.

Product recommendation: GS08A


Wc 8co Tunsgten Carbide Grits




Weld Materials,Tubular Welding Rod,Welding Electrodes,Stainless Steel Welding Rod

Luoyang Golden Egret Geotools Co., Ltd , https://www.xtclasercladding.com