If you are going to start an auto repair shop or repair company, auto sheet metal and painting projects are indispensable, so you need to configure the corresponding painting equipment and tools, and how to use the funds on hand more effectively. This may be your most concern. The problem is described below. (1) Configuration of painting room 1) Configuration purpose. Spray booth is one of the most important equipments for auto repair and painting operations. The purpose of the painting booth is to provide a clean, safe and well-lit painting environment for the car painting construction, so that the spraying construction will not be disturbed by dust, and the painting quality will be guaranteed, and the volatile paint mist will be confined to a limited space to reduce environmental pollution. 2) Technical requirements for spray booths. 1 The air entering the paint booth must be strictly filtered to ensure that there is no dust in the air. 2 The air flow in the paint booth must flow from the ceiling to the ground in the direction of gravity, and the air is discharged from the ground and filtered to be cleaner air. 3 Ensure that the air between the paint booths is converted twice per minute. Therefore, the indoor air flow rate should be 0.3-0.6/s. The air flow rate is too large, the paint loss is too much, the coating condition is poor, and the air flow rate is too small, affecting the normality of the solvent. Volatilize. 4 has good lighting conditions. 5 Make sure that there is no negative pressure in the paint booth. This can be achieved by controlling the intake and exhaust volumes. The amount of air entering the paint booth should be slightly more than the amount of exhaust gas. 6 The noise of the painting booth shall not exceed 85dB.7 The fireproof requirements shall be met. 3) Classification of paint booths. The spray booths can be divided into two categories, dry and wet, depending on the way they remove paint mist and prevent dust from mixing. 1 dry painting room. The dry spray booth is mainly composed of a chamber body, a filter, an exhaust pipe, and a ventilator. It is characterized by its simple structure, low paint loss, high coating efficiency, reduced water treatment equipment due to non-use of water, and low cost, and is widely used by domestic small and medium-sized repair companies. 2 Wet spray booth. Wet spray booths are divided into four types: shower type, curtain type, text type, and rotary type. For high-grade automotive finishes, foreign countries often use text-based or water-based rotary spray booths, which are rarely used in China. 4) Maintenance of painting room. 1 All preparations before painting should be done outside the paint booth. 2 The filter must be checked and replaced regularly. 3 Check the barometer reading every day, master the pressure range of the spray booth, and strictly prohibit negative pressure. 4 The dry painting booth should wet the ground before spraying to facilitate dust protection. 5 Regularly check the lighting conditions and replace the weak or burned lamps. 6 Regularly lubricate the exhaust fan and motor. 7 pay attention to personal hygiene, it is strictly forbidden to enter the paint booth with dirty clothes. 8 After each painting operation is completed, it shall be thoroughly cleaned and the related equipment in the painting booth shall be maintained and cleaned. (2) Configuration of paint booth 1) Configuration purpose. 1 After the car finishes spraying, from the customer's point of view and from the point of view of the maintenance company, it is hoped that the paint will reach the non-dusting state as soon as possible. One of the reasons is to increase efficiency and save time. The main reason is that the coating effect is guaranteed. If the surface cannot be dried quickly, the possibility of dust attachment is greatly increased. 2 to ensure the overall performance of paint after painting. If only fast drying is required, we can choose a quick-drying type refinish paint, but considering the quality of the paint and the overall performance of the paint should be taken into consideration in all aspects, we can't just pursue quick drying regardless of its performance, so the best solution Is to configure paint room. 2) Technical requirements for paint booths. 1 The paint room must be clean, dust-free, and air is strictly filtered. 2 baking temperature can meet the technical requirements of different coatings. 3 In the paint room, an exhaust device must be installed so that the solvent and decomposed substances that evaporate from the coating film during the drying process do not exceed a certain concentration, so as to prevent the drying speed, quality, and even explosion of the paint film. 4 Solvent-based paint wet film should be allowed to leave a certain period of time before drying, so that most of the solvent in the paint film volatilizes and leveling, can reduce the "orange peel", "pinhole" "blister" and other defects. 3) Classification of paint booths. According to different drying methods for paint film, paint room can be divided into drying type and irradiation curing type. 1 drying paint room. Drying paint room can be divided into natural convection, circulation fan convection and far infrared radiation type 3 kinds. At present, far-infrared radiation-type paint booths are widely used in domestic maintenance enterprises. The far-infrared radiation-type paint booths generally have a heating temperature range of 38-83°C. Vehicle repair companies can flexibly select the number of equipment-based infrared lamps according to the size of the baking operation. position. The far-infrared heating energy conversion mode is mainly heat radiation, so compared with the hot air circulation heating mode, the possibility of dust adhering to the paint surface is greatly reduced. The drying of the paint surface by far infrared radiation not only shortens the drying time of the paint film (from one day to 30-50 min), but also improves the working efficiency and helps to improve the quality of the paint application. 2 irradiation curing paint room. This type of paint room has two kinds of photocuring and electron beam curing, and it is rarely used in the general refinishing coating industry. (3) Spray paint booth configuration. In the past, independent paint booths and paint booths were introduced. In actual production practice, manufacturers usually start from the practicability and economy of the maintenance companies and combine paint booths and paint booths into one, namely painting and painting dual-use rooms. It combines the technical properties and functions of paint booths and paint booths. Its characteristic is that the air purification is good. After the painting vehicle is coated, it may not move, which is convenient for construction operation and daily maintenance. At present, there are many kinds of spray paint booths used in China, among which domestically-produced equipment are Jiangsu Zhongda, Beijing Dream Star, Wuxi Yuntong, and North Tiyou. Imported equipment includes Gree, Luhua, and Baozhibao. (4) Configuration of spray gun 1) Classification and model of spray gun. There are many kinds and types of spray guns. Although the naming methods of painting equipment manufacturers are different, there are generally the following classification methods. 2) According to the type of nozzle, it is divided into two types: nozzle type and flat type. 2 According to the paint supply method is divided into siphon type, gravity type, pressure feed type 3 kinds. (2) Selection of spray gun 1) Select according to the different construction objects of the maintenance company. For paint spraying of passenger cars and trucks, PQ-1 domestic spray guns can be used, which are low in price and easy to maintain. For construction with higher requirements for coating quality, it is best to use domestic flat-nozzle siphon or imported spray guns. 2) Select large, medium and small spray guns according to the size of maintenance work. Small spray guns produce less than 100g per minute, medium spray guns have 180g per minute, and large spray guns have more than 200g per minute. 3) Select according to different spraying construction items. In general, spray lacquers mostly use large diameter spray guns, middle caliber spray guns are used for middle coating, and small caliber spray guns are used for spray top paints. 4) In the special lacquer repair construction, special repair lances can also be used. Repair guns abroad major manufacturers and models. 5) Configuration of the spray gun supporting equipment. In the coating construction, only the spray gun can not work, but also need to match the air compressor, air filter and air-guiding hose according to the requirements of the painting construction and the construction conditions. Refer to the description of different spray guns. Specific configuration.
This catagory includes outside door handle, inside door handle and tailgate handle for Nissan Versa, Murano, Qashqai, Pathfinder, Altima, Rogue, 350Z and etc.
Car Door Handle For Nissan,Nissan Car Door Handle Replacement,Pathfinder Car Door Handle Repair,Qashqai Car Door Handle Accessoires RUIAN XINGTING AUTO PARTS CO.,LTD , https://www.xingtinghandle.com
Interior car door handles is a small lever that you pull to release the door's hook from the vehicle frame's latch. There are different forms of inside door handles, though the area where it's mounted remains consistent with most types of vehicles.
The tailgate handle is an external component that triggers the latch mechanism and allows the tailgates to swing open.
Most handles are made of plastic, while some are metal, such as zinc alloy. Further, there are designs offering a mix of both like a plastic bezel and metal lever, or vice versa.
For the car door handle surface finish, there are tons of them available. The list includes the usual chrome-plated, primed, smooth or textured, chrome bezel and colored lever combination, paint to match, satin chrome, and polished.
Automotive paint paint considerations