5K 10K Running Medals,Medal Virtual Challenge,Personalized Race Medals,Custom Race Medals ZHONGSHAN LAVI HARDWARE PRODUCTS CO., LIMITED , https://www.lavihareware.com
Technical Parameters:
â—† External power supply: 220V AC or 24V DC
â—† Input
Signal: Receive a signal from a VS Series Vibration Speed ​​Sensor
Sensitivity: 20mV/mm/s±5%
Frequency response: 5 ~ 300Hz
◆ Range: 0 ~ 500μm (peak - peak) or 0 ~ 50.0mm / s (true RMS)
â—† LED indication: OK green, Alert, Danger red.
◆ Measurement error: ±1% of full scale
◆ Current output: 4~20mA active, output load ≤500Ω
◆ Alarm point setting: 0~100% full scale, accuracy ±1%
â—† Alarm reset mode: automatic or manual (site reset button, remote alarm reset terminal)
â—† Relay seal: epoxy resin, node capacity DC30V/5A or 220V/5A, single pole double throw
â—† Power-on delay: about 10 seconds
◆ Temperature range: -25°C~+65°C during operation, -40°C~+85°C during storage
â—† Relative humidity: up to 95%, no condensation
Technical Parameters:
â—† External power supply: 220V AC or 24V DC
â—† Input
Signal: Receive a signal from a VS Series Vibration Speed ​​Sensor
Sensitivity: 20mV/mm/s±5%
Frequency response: 5 ~ 300Hz
◆ Range: 0 ~ 500μm (peak - peak) or 0 ~ 50.0mm / s (true RMS)
â—† LED indication: OK green, Alert, Danger red.
◆ Measurement error: ±1% of full scale
◆ Current output: 4~20mA active, output load ≤500Ω
◆ Alarm point setting: 0~100% full scale, accuracy ±1%
â—† Alarm reset mode: automatic or manual (site reset button, remote alarm reset terminal)
â—† Relay seal: epoxy resin, node capacity DC30V/5A or 220V/5A, single pole double throw
â—† Power-on delay: about 10 seconds
◆ Temperature range: -25°C~+65°C during operation, -40°C~+85°C during storage
â—† Relative humidity: up to 95%, no condensation
BSQ, HZD-B vibration transmitter vibration transmitter HZD-B-9F, DC24V integrated vibration and temperature transmitter JX73ST-40-A-85 Integrated vibration and temperature transmitter is a small integrated Transmitter. Its 4-20 mA output signal is proportional to the true rms RMS of the vibration velocity of the measured object. The transmitter uses a micromachining process to integrate the sensor. The vibration electrical signal is passed through a bandpass filter, converter, amplifier, and true RMS RMS converter. Finally, the voltage/current drive circuit generates a 4-20 mA standard current signal output. Because the transmitter can easily measure the vibration speed within the specified frequency range of the vibrating object
Vibration Transmitter Vibration Probe Measure Rotary Machinery Shaft Vibration Shaft Vibration Transmitter is used with eddy current sensor. It can be widely used in large rotating machinery shaft vibrations in electric power, metallurgy, petrochemical, steel and paper industries (rotor relative bearing) Measurement and protection control of the vibration of the cover. It mainly monitors the radial vibration of the rotating machine rotor, monitors the vibration-increasing machine monitoring and protection device caused by the imbalance of the rotor, misalignment, loose parts, etc. JM-B-3E dual-channel vibration monitoring and protection device, JM-B- 7 intelligent vibration monitoring and protection instrument, JM-B-201 intelligent vibration temperature detector differential monitor, RDXZ series shaft vibration monitor, CZJ-B system 151/OD-162/OD-165 eddy current axis displacement sensor shaft vibration probe front EC-001/EC-002/EC-003 eddy current axis displacement sensor shaft vibration probe extension cable PR6422/PR6423/PR6424/PR6425/PR6426 eddy current axis displacement sensor shaft vibration probe CON011/91, technical parameter sensitivity 20~50mv /mm/s±1% (according to user adjustment) Frequency response (optional) 5~100hz, 10~500hz, 10~1000hz natural frequency about 10hz amplitude limit 2mm (peak-peak) Zui large acceleration 10g installation mode vertical; horizontal Vertical and horizontal dual-use temperature range -30°C~120°C Relative humidity to 95% Non-condensing Dimensions φ35×78mm Weight Approx. 350g Mounting thread m10×1.5 Ordering Guide Selection code trlv-a□□-b□□Select Type Description Sensitivity a□□01, JM-B-4 Vibration Temperature Monitoring Protection instrument, JM-B-3Z intelligent vibration monitoring and protection instrument, JM-B-6Z (402) monitoring and protection device, JM-B-5S vibration monitoring and protection instrument, JM-X-3 series intelligent travel monitoring and protection instrument, JM- X-3W intelligent axial displacement monitoring and protection instrument, JM-X-3Z intelligent differential expansion monitoring and protection instrument, JM-C-3 series intelligent speed monitoring and protection instrument, JM-C-7F wall-mounted anti-speed monitoring and protection instrument, JM -C-5S speed monitoring and protection device
Vibration Transmitter HZD-B-9F, DC24V
Vibration Transmitter HZD-B-9F, DC24V