First, the vehicle configuration

The sweeper type using Furui Ka States east three types of chassis modification, installation sub-engine, turbine, water boxes, bins, approximately vertical sweep, the rear sucker, sweeping dust disk system, hydraulic system, dedicated electronic control means The system and sub-frames are converted (pre-punched and sprinkled)

1, Fu Ruika DF (wheelbase 3300) State â…£ types of chassis type, turned with the front cab, with the original direction of power, 700--. Steel tire 16, front and rear axle with shock absorbers air. Equipped with Dongfeng Chaochai Engine, 95 hp, low fuel consumption.

2. The auxiliary engine adopts the Jiangxi Isuzu 57Kw engine with strong performance.

3. The automatic clutch drives the fan to reduce the impact on the engine when the fan starts and stops . The clutch has advantages of high wear resistance, long service life, low noise, low fuel consumption, and cost saving during use .

4, using Luoyang listed companies, Beibo Taixin high-power wear-resistant maintenance-free centrifugal fan, no noise, high efficiency and large amount of air, long service life.

5. The clean water tank makes full use of the on-board space and has a volume of 1.5 m3. It has a built-in water level alarm. The water tank has internal anti-corrosion, anti-rust and anti-virus treatment, which makes the water pump run more safely and guarantees the cleaning efficiency.

6. The dustbin adopts a double-layered stainless steel structure with a volume of 4 m3 . The interior is equipped with a filter screen, which can effectively prevent the air, plastic bags and the like from blocking the air outlet and dust discharge. The built-in spray duster maximizes the space for litter bins. The car body is tilted and unloaded.

7. The left and right vertical sweeper is a single sweeper. The front sweeper has an automatic avoidance function, which reduces the number of sweepers and sweeper consumption, and can reduce the use cost. A water spray device is installed on the brush to spray dust. Left and right sweeps separate control, which can realize different operation modes such as post sweep and full sweep.

8. The suction mouth width of the suction nozzle reaches 1100mm, and the maximum total working width is greater than 3.2m. Three height-adjustable nozzle wheels can adjust and ensure a reasonable clearance between the nozzle and the road surface, so as to achieve better suction effect and higher suction efficiency.

9. The manual push button hydraulic system of the cab drives the left and right vertical sweeping movements, the left and right swash plate rotation, the nozzle lifting and lowering, the opening and closing of the rear door of the garbage can, and the tipping reset of the dustbin.

10. The swash plate cycloidal motor adopts domestic famous brands, with long and stable service life and low failure rate.

11. The hydraulic pipeline adopts the German standard technology sealing structure, which has good anti-vibration performance and high sealing reliability. It can realize the sealing effect without leakage.

12, the use of high-quality hydraulic solenoid valve, the key electronic control components using Siemens electrical switch, high reliability, long service life.

13, hydraulic components using integrated design, electro-hydraulic centralized control of the cab, easy to operate.

14, install a manual pump emergency system, in the state of the auxiliary engine can also lift litter box, easy maintenance.

15. LED warning lights are used at the rear to ensure safe operation.

16, non-stainless steel parts by electrophoretic rust treatment, durable.

17. The load-bearing beam of the sub-frame is welded with square steel with a section length of 120mm, width of 60mm and thickness of 8mm, which ensures the safety of the vehicle and makes the vehicle safer.

18, appearance design computer design, high side skirts, surface transition, the overall coordination of symmetry. Achieve low fuel consumption, low noise, streamlined design.

Second, the main technical parameters

1. Overall dimensions of the vehicle: Length 6 150mm Width 22 3 0mm Height 2 55 0mm

2. The total mass of the vehicle: 7300 Kg rated load quality: 2000 Kg Curing mass: 5170 Kg

3. The vehicle can reach a top speed of 9 0 Km / h, the cleaning speed: 3-25Km / h

4. Cleaning efficiency: ≥95%

5. The maximum suction particle size: 100mm

6. Maximum discharge angle of trash can: 45°

7. Maximum cleaning width: 3.2m

8. Maximum cleaning capacity: 70000m2/h

9. Hydraulic tank capacity: 60L

10. Sub engine working speed: 1750r/min

1 1. Trash capacity: 4 m3

1 2 . Water tank capacity: 1.5 m3

Third, chassis technical parameters

1. Chassis model: DFA1 070SJ35D6

2. Wheelbase: 3 3 00mm

3. Emission Standards: State III

4. Tire specifications: 7. 0 0-16LT 14PR, 7. 0 0R16LT 14PR

5. Number of tires: 7

6. Number of riders in the cab: 3 persons

7. Engine Model: CY4102-CE4F

 

Tel 0722-3821899 Contact person, Zhou Zhongxing

Http :// WWW . HBCL99 . COM

Sales Hotline: 15897596858
Office Phone: 0722-3821899
E-mail:

Semi-automatic Strapping Machine is mainly suitable for carton packing. It can be used alone or with Assembly Line.It is widely used in household appliances, textiles, food, Department stores, pharmaceuticals and chemical industries. It is suitable for the occasion where the size of carton changes little frequently, especially for the continuous sealing of cartons with the same specifications.

Strapping Machine

Shenzhen Hongdali Machinery Co.,Ltd , https://www.conveyortop.com