The new type of road sweeper is a newly developed road cleaning vehicle that integrates cleaning and sweeping. It integrates the advantages of the existing sweeper and cleaning vehicle, completes daily operations without dust, and does not accumulate water on the road surface. The sweeping light can also be adapted to the requirements of different polluted roads and meet the differentiated operational requirements of users. It is suitable for sanitation cleaning and pavement maintenance of urban roads, plazas and docks. The vehicle's job control device is composed of PLC programming electronic control system, hydraulic system, and pneumatic system. The operation of the switch button in the cab can achieve the implementation of all actions, minimizing the driving operator's due to the cumbersome operation information. Mental pressure, operation operations are full of humanity. The cleaning sweeper is mainly composed of a chassis, an auxiliary engine system, a blower device, a suction nozzle device, a front scrubbing device, a clean water tank, a sewage garbage can, a hydraulic system, an air circuit system, a circuit control system and other important assembly devices. The high-pressure water curtain replaces the traditional sweeping brush. The high-pressure water flow is used to flush the road waste, and the waste is collected along with the sewage to the suction nozzle device 5 to be sucked and recovered. The sewage is filtered and can be reused. This operation mode can not only clean the road surface area, but also function to sweep the road vehicle. At the same time, it will not cause dust and water on the road surface and cause secondary pollution, thus solving the shortcomings of the traditional road sweeper and cleaning vehicle. Also used is a unique cleaning, sweeping, suction integrated V-shaped device and high-efficiency front sweep brushing device. The new cleaning sweeper truck operation control device operation control device is an important device for the cleaning vehicle to complete various tasks and coordinate the work of the various systems. The following describes the type of cleaning sweeping path from three aspects: PLC programming electronic control system, hydraulic system, and pneumatic system. Car work control device. 3.1 PLC programming electronic control system job control device. The electronic control system and the electronic control system of the sweeper chassis are two independent systems. The electronic control system of the operation control device consists of an electric control box, an auxiliary engine electrical element and a solenoid valve group. The electric control box is installed in the middle of the cab, and is used for the control and auxiliary engine of each working device, solenoid valve, and combination warning lamp. Speed, water temperature, oil pressure and other monitoring. [3] The front scrub water spray system is also controlled by the PLC programming electronic control system. When the current scrubbing device is lowered and the scrubbing is rotated, the electronic control system controls the opening of the electromagnetic water valve valve, and the clean water passes from the clean water tank via the copper ball valve and the precision water filter. Through the electromagnetic water valve to reach the diaphragm pump, and then distributed to the left and right plate sprinkler mechanism and roller brush sprinkler mechanism to achieve water spray work. The hydraulic system adopted by the new hydraulic cleaning system for road sweepers is an open system and an electrohydraulic centralized control and control method. The main components of the system include gear pumps, hydraulic motors, hydraulic cylinders, manifold blocks, solenoid valves, throttle valves, one-way valves and hydraulic accessories. The hydraulic system has two gear pumps. One is mounted on the rear side of the flywheel housing of the auxiliary engine. It is a constant meshing type. This pump mainly supplies the four hydraulic motors of the front scrubbing device and all the hydraulic cylinders. The other one is installed at the power take-off of the auxiliary engine gearbox and uses air-controlled engagement and disengagement. The operation control switch is on the panel of the electric control box of the cab. The pump is mainly used for fan hydraulic motor to adjust the hydraulic system. The main system overflow is. Flow pressure, front scrub speed, front scrub lift and back door switch speed, and left and right nozzle swing and retract speed adjustments. The electromagnetic relief valve sets the pressure before scrubbing. The new type of sweeper makes full use of the gas resources of the chassis and consists of the air system used. The air system mainly controls the opening and closing of the high-pressure ball valve of the waterway and the lifting and lowering of the suction nozzle. The air source is taken from the chassis, and the one-way sequence valve can ensure that the chassis air pressure reaches a certain value before it reaches the gas. The new cleaning sweeper adopts high-pressure current-collecting sweeping nozzle, cleaning vehicle self-avoidance spray cleaning mechanism, sanitation vehicle road brushing device, sanitation vehicle road surface and road shoulder stone brushing device, and other technologies for traditional garbage suction sweeping and cleaning vehicles. The way of pavement cleaning was innovative and breakthrough. The work control device has a reasonable and reliable design, and the product is in good condition. In the highly automated development of science and technology and the highly automated production, the harm of static electricity is obvious. It causes various obstacles and affects the quality of products. Especially in the dangerous places where pyrotechnic products exist, static electricity can not only cause huge economic losses, but also directly threatens. Personnel life, equipment and facilities. Therefore, it is very meaningful to formulate practical and feasible anti-static hazard measures, and it is also the responsibility of each technical personnel engaged in pyrotechnics production. In addition, electrostatic protection requires a systemic measure and must be protected from all aspects to effectively control the hazard of static electricity. In the future, in the production process of pyrotechnics, the operation speed should be specified in detail. The surface resistivity of the tooling and equipment directly contacted with the product can also be reduced by the application of an antistatic agent and other chemical methods to accelerate the electrostatic discharge. The surface of the material becomes smooth and the coefficient of friction decreases, thereby reducing the amount of static electricity generated during the contact separation process. In short, electrostatic protection of explosives needs continuous exploration.
Our company have 20 years experience doing all kinds of Construction Machinery Parts, such as bulldozer blade for shantui, ripper for shantui,excavtor bucket for shantui, Wheel Loader bucket, arm, bucket teeth, cutting edge, side cut edge,end bit, cutting blade.
Our company have all kinds of equipments to keep all the parts produce by high quality, welding robot, laser cutting machines, bending machiner,drilling machines etc. To keep the products do as your required, we also have many equipments for inspection, such as Metal flaw detector, three-coordinates measuring machine automatic painting line, all of the equipments keeps good products.
Exhibition
Excavator Bucket,Rock Excavator Bucket,Wheel Loader Bucket,Backhoe Excavator Bucket SHANDONG HE FORK TRUCK CO.,LTD. , https://www.shantuimachinery.com
Buckets Series
About Shandong volin heavy machinery co,.ltd.
Advanced equipments.
Q1: Are you factory or trading company?
New cleaning sweeper operation control device
As doing this bucket more than 10 years,we can do all kinds of buckets as you required.the buckets avalivable brand and model as following:
Buckets For Brand excavator
Model
capacity(m3)
305.5
0.15~0.3
307/308
0.2~0..4
312C/D,315
0.4~0.65
320B/C/D
0.6~1.3
324C/D/DL
1.2~1.6
325C/D
1.2~1..6
329D/DL
1..1~1.8
330B/C/D
1.2~1.8
336/345
1.4~2.5
E70B
0.25~0.5
E200B
0.6~1.0
Buckets For Brand excavator
model
capacity(m3)
PC35/40/50
0.12~0.2
PC55/60
0..2~0.37
PC70/100
0.3~0.6
PC120/130/160LC
0.3~0.7
PC200/210/210LC
0.35~1.3
PC220/220LC
0.8~1.3
PC270
1.3~1.5
PC300/350/360
1.2~1.8
PC400
1.6~2.2
PC450
2.0~2.8
Buckets For Brand excavator
model
capacity(m3)
R55/60
0.15~0.3
R80
0.2~0.4
R110/130
0.3~0.65
R200/210
0.8~1.0
R225
0.9~1.2
R265/305
1.2~1..6
R335
1.3~1.8
R375
1.5~1.9
R455
2.0~2.8
Buckets For Brand excavator
model
capacity(m3)
ZX35/50
0.15~0.2
ZX55/60
0..1~0.28
ZX65/70
0.28~0.38
ZX120/130
0.5~0.7
ZX200/210
0.8~1.2
ZX260/270
1.3~1..5
ZX330/360
1.35~1.8
ZX470
1.9~2.5
ZX870
3.0~5.5
Buckets For Brand excavator
model
capacity(m3)
SK60/80
0.25~0.6
SK100/120/135
0.25~0.8
SK200/210
0.5~1.3
SK230/250
1.0~1.4
SK300/330
1.2~1.6
SK350
1.6~1..8
SK480
1.6~3.0
Buckets For Brand excavator
model
capacity(m3)
SH60
0.25~0.4
SH120
0.4~0..6
SH200
0.6~1.1
SH220/240
1.0~1.4
SH280/300
1.2~1.5
SH330/350
1.4~1.8
Buckets For Brand excavator
model
capacity(m3)
JS130
0.25~0.6
JS160
0.35~0..7
JS200
0.5~1.0
JS220
1.0~1.4
JS370
1.4~1.9
BT130
0.25~0.5
BT210
0.7~1.1
Buckets For Brand excavator
model
capacity(m3)
DH55/60
0.12~0.3
DH80
0..2~0.42
DH150
0.25~0.6
DH215/220/225
0.6~1.1
DH300
1.3~1.6
DH380
1.4~1.8
Buckets For Brand excavator
model
capacity(m3)
HD250/307
0.2~0.4
HD450/512/550
0.4~0.65
HD700/800
0.3~0.65
HD820/900
0.8~1.0
HD1250/1430
0.9~1.2
HD1880
1.2~1..6
Detailed Images
Packing & Delivery
The standard packing is by plywood pallet,with a steel plate fixed on the pallet, it is stable and easy transport by forklift.With water proof plastic film outside,it can protect the painting from demage and water.
When loading container,we will fixed the pallet on the container follor,keep the bucket in best quality is our first aid.
FAQ
We are factory,our location is No.6 Jiejia Road High-tech zone,Jining city,Shandong province.Welcome visit us.
Q2: How can i make payment?
We accept T/T and L/C at sight, usually by 30% down payment, balance before shipment.
Q3: How is your warranty?
6 Months from BL Date
Q4: Which is the nearest port?
Qingdao Port